Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
EttCM energy technology ( Learning and Teaching tool ) The Permanent Magnetic power source;
The EttCM energy technology ( Learning and Teaching tool ) is an information of Technology on how it is possible to use
Permanent Magnetic Potential Energy as a main source of generating usable energy output in a machine or device built to
use this form of energy conversion system;
There are 2 parts to the system the first part uses Potential energy only; and does not use energy or produce energy output
The second part uses the potential energy from the first part to develop usable kinetic energy of motion from the use of
magnetic induction to ferrous or iron type materials:
The First part of the system; is used to decrease and increase the attraction to the ferrous or iron metals
Thermodynamics says: A decrease of energy or force must happen in order to produce energy of movement;
The decreasing is produced by pushing 2 magnets of the same poles together that reduces the attraction to the ferrous
metals used in the motor machine or device;
moving the magnets apart increases the attraction to normal power of attraction: this is shown in 2 test done below:
As shown when the 2 magnets are pushed against the single magnet the force of attraction is reduce to 1/ 4 lbs. or 120 grams
In the second test the magnets are moved apart returning the pull force back to normal
The pull force is about 2 lbs or 900 grams tested using a scientific scale
This decreasing and returning to normal power can be used in a motor type device shown below
Because all the magnets are repelling in force equal: the wheel is in balance: like a car tire in balance it is very easy to move
and rotate only the bearing friction is needed to move and rotate the wheel
This design is like a radial motor using cylinder type sliders where the magnets are moved back and forth as the wheel
rotates: ( As the wheel rotates the magnets are pushed together at the bottom and moved apart at the top
Again: --- No input energy is needed to rotate the wheel only bearing friction ---
((( What this means is the system that produces the attraction of decreasing and increasing the power output ---
does not use input energy of any type to make the output usable power -- )))
The top view of the testing motor is shown that relates to the design of the induction system used on the drawing below:
The thick white line on the right side is the induction steel plate
Because the Wheel only used bearing friction that is about 1/8 lbs or 60 grams - most of the output force is converted to usable energy of motion and output power;
In the tests shown above when the magnets are apart there is a 2 lbs pull force
When the magnets are pushed together the power of attraction is reduced to 1/ 4 lbs
2 lbs - 1/4 + 1/8 = about 1 and 1/2 lbs or about 720 grams or pull forward power
The magnets are being made to decrease and increase their attraction force to the ferrous metal plate;
in a constant movement of rotation:
( This uses NO energy inputs to produce this effect ( saying no energy is use to produce usable energy power output )
The wheel is rotated by the force of induction producing Kinetic energy of motion that makes the wheel rotate:
The power of 2 lbs of being used to make the output power uses some to keep the wheel rotating;
But most of the output power using this form of technology is usable:
Self contained; self starting once built; can work anywhere even in Space:
This is a ( learning and teaching tool ) used to show how to produce 1 form of usable energy and power systems
from Permanent Magnetic potential energy only; NO outside energy input are needed to make the usable output
power this technology produces;
( Note: This is only A learning and teaching tool ) This all conforms to the laws of Physics and thermodynamics;
This technology ( IS NOT ) perpetual motion, free energy, overunity, zero point energy or the rest;
It falls in a new category; Call ( Cooldynamics ) that is magnetic or Gravity type Cold energy only;
Where thermodynamics is hot energy only;
Everything shown is real and true: all system have been tested and shown to be true;
Because this is an open forum where anyone can make their own opinion on this subject: all opinions are true to the owner
of the opinions made; being said: free will to comment in any way; positive or not positive all have the right to say whatever they wish and have; but still belongs to the owner of the opinion commenting; Whatever said: does not change the how and why, the technology works or the learning and teaching tool presented; thank you:
Energy to torque Conversion Motor - systems - Washington state - USA
Permanent Magnetic Potential Energy as a main source of generating usable energy output in a machine or device built to
use this form of energy conversion system;
There are 2 parts to the system the first part uses Potential energy only; and does not use energy or produce energy output
The second part uses the potential energy from the first part to develop usable kinetic energy of motion from the use of
magnetic induction to ferrous or iron type materials:
The First part of the system; is used to decrease and increase the attraction to the ferrous or iron metals
Thermodynamics says: A decrease of energy or force must happen in order to produce energy of movement;
The decreasing is produced by pushing 2 magnets of the same poles together that reduces the attraction to the ferrous
metals used in the motor machine or device;
moving the magnets apart increases the attraction to normal power of attraction: this is shown in 2 test done below:
As shown when the 2 magnets are pushed against the single magnet the force of attraction is reduce to 1/ 4 lbs. or 120 grams
In the second test the magnets are moved apart returning the pull force back to normal
The pull force is about 2 lbs or 900 grams tested using a scientific scale
This decreasing and returning to normal power can be used in a motor type device shown below
Because all the magnets are repelling in force equal: the wheel is in balance: like a car tire in balance it is very easy to move
and rotate only the bearing friction is needed to move and rotate the wheel
This design is like a radial motor using cylinder type sliders where the magnets are moved back and forth as the wheel
rotates: ( As the wheel rotates the magnets are pushed together at the bottom and moved apart at the top
Again: --- No input energy is needed to rotate the wheel only bearing friction ---
((( What this means is the system that produces the attraction of decreasing and increasing the power output ---
does not use input energy of any type to make the output usable power -- )))
The top view of the testing motor is shown that relates to the design of the induction system used on the drawing below:
The thick white line on the right side is the induction steel plate
Because the Wheel only used bearing friction that is about 1/8 lbs or 60 grams - most of the output force is converted to usable energy of motion and output power;
In the tests shown above when the magnets are apart there is a 2 lbs pull force
When the magnets are pushed together the power of attraction is reduced to 1/ 4 lbs
2 lbs - 1/4 + 1/8 = about 1 and 1/2 lbs or about 720 grams or pull forward power
The magnets are being made to decrease and increase their attraction force to the ferrous metal plate;
in a constant movement of rotation:
( This uses NO energy inputs to produce this effect ( saying no energy is use to produce usable energy power output )
The wheel is rotated by the force of induction producing Kinetic energy of motion that makes the wheel rotate:
The power of 2 lbs of being used to make the output power uses some to keep the wheel rotating;
But most of the output power using this form of technology is usable:
Self contained; self starting once built; can work anywhere even in Space:
This is a ( learning and teaching tool ) used to show how to produce 1 form of usable energy and power systems
from Permanent Magnetic potential energy only; NO outside energy input are needed to make the usable output
power this technology produces;
( Note: This is only A learning and teaching tool ) This all conforms to the laws of Physics and thermodynamics;
This technology ( IS NOT ) perpetual motion, free energy, overunity, zero point energy or the rest;
It falls in a new category; Call ( Cooldynamics ) that is magnetic or Gravity type Cold energy only;
Where thermodynamics is hot energy only;
Everything shown is real and true: all system have been tested and shown to be true;
Because this is an open forum where anyone can make their own opinion on this subject: all opinions are true to the owner
of the opinions made; being said: free will to comment in any way; positive or not positive all have the right to say whatever they wish and have; but still belongs to the owner of the opinion commenting; Whatever said: does not change the how and why, the technology works or the learning and teaching tool presented; thank you:
Energy to torque Conversion Motor - systems - Washington state - USA
Powered by leedskalnin.com & buzzdev.net